Do you need help? Please call us at (918) 627-7777.
Hours & Directions
You’ve probably heard of the 4 Cs of diamond grading. I’ve ranked them below, in terms of importance when you choose a diamond.
Now, we’ll go through the evaluation of each property.
One of the hardest properties to judge, the cut is nevertheless the most important. Choosing a well-cut diamond requires paying careful attention to a few key characteristics.
Brilliance: Brilliance refers to the total amount of light returned by the gem. A cut gem’s pavilion facets should act as mirrors, reflecting the light entering the stone back to the observer. The cut plays a critical role as the angles at which a diamond is cut affects greatly how efficiently it reflects light as this impacts how well the diamond sparkles. Unfortunately, diamond cutters can’t cut all mined diamonds to excellent proportions. Often, they must compromise between maximum brilliance and maximum yield (weight/carat retention). If cutters remove too much material from the diamond rough, they may cut away their profit. Thus, for economic reasons, many diamonds receive a cut with less than ideal proportions. However, if a cutter varies a little further from the ideal cut angles, the diamond’s brilliance begins to suffer. If the cutter varies too far, you’ll get a diamond that just doesn’t compare to others in brilliance or fire.
Please understand, the information above assumes we’re talking about round diamonds. Cutters can cut all their major facets at the same angle due to the round’s symmetrical proportions. For other shapes, this doesn’t hold true. For example, many people prefer a marquis shape. This is fine, but don’t expect a marquis, or any other shape, to have the brilliance of a round. A marquis requires cutting a number of facets just to accommodate the shape. Cutters cut these facets at angles that vary from those that give the greatest brilliance. This is a simple fact: the more facets cut at the ideal angle, the greater the gem’s brilliance.
Another factor to consider when you choose a diamond is its shape. An ideal cut diamond should be symmetrical, not lopsided. A poorly proportioned gem can be “camouflaged” in its setting. Thus, you might not notice it until after you’ve bought it. Always examine a diamond loose, not in the setting.
In terms of resisting scratches, diamonds are famously the hardest material in the world. However, in terms of resisting blows, they’re brittle. This property affects the cut evaluation, particularly when examining the girdle. A gem’s girdle is its widest part when viewed from the top but its thinnest when viewed from the side. If a gem cutter cuts the diamond’s girdle too thin, it can present a weak area, just asking for trouble. Some girdles get cut to a knife-edge level of thinness. Definitely avoid this, because it can cause the gem to fracture or break.
The closer to colorless, the greater a white diamond’s value. GIA’s color grading system for white diamonds begins with the letter D and goes to Z.
The further the grade goes down the alphabet, the stronger the tinting and lower the diamond’s value. However, once you get to the extreme end and the color becomes richer, you have a fancy colored diamond. No longer considered “off colored” white diamonds, their value starts going up again.
The size and number of inclusions inside a diamond determine its clarity. An inclusion can be another mineral, a fracture, or occasionally a void. Simply put, anything that will interfere with the free passage of light in a gem qualifies as an inclusion. The highest grade a diamond can get is flawless. That means you can see no inclusions at 10X magnification. However, this doesn’t mean you can’t find inclusions with higher magnification. Also, don’t assume it’s the only grade with no inclusions visible to the naked eye.In addition to F for flawless and IF for internally flawless, clarity grades use the letters V,S & I. They stand for Very, Small, and Inclusion. Numbers 1 to 3 further designate levels within grade.
After F and IF, clarity grades proceed as follows:
All these clarity grades indicate diamonds with no inclusions visible to the naked eye. These are all eye clean. Further down the grading scale, you’ll find I1 and I2 diamonds. These have eye visible inclusions. However, they’re still considered gem grade.
You may encounter diamonds so heavily included that they are not usually considered gem grade, because so little light will pass through them. However, since they still have the magic name “diamond,” they do show up on the market regularly.
Before you choose a diamond, beware of ads promoting a 1-carat diamond ring for a very low price. Not all diamonds are considered gems. Nevertheless, the vast majority of mined diamonds are usually considered industrial grade.
By far, carat or weight is the easiest quality factor to understand when you’re shopping for diamonds. Simply put, small diamonds are more common than large ones, but larger stones are more desired. Therefore smaller diamonds cost less per carat than large ones. This explains why you’ll encounter jumps in price per carat as diamond sizes increase.
Occasionally, looking for a lower clarity graded diamond may be worthwhile. This depends on the individual diamond and setting. Sometimes, the eye-visible inclusion that made it rank lower may have an insignificant effect on its appearance. Overall, the stone may still look delightful.
However, going down further in quality in other areas is rarely worthwhile. Without making a comparison with better quality diamonds, customers often convince themselves they’ve found a great deal. When they make the comparison later, they find disappointment.
Selecting a diamond is a personal thing. Of course, not everyone will have the same opinions. However, consider this observation carefully before you choose a diamond. In my experience, most folks will enjoy a smaller, higher quality dazzler more than a larger but mediocre gem.
Let’s say you look at two well-cut diamonds side by side. One has grades of D and VVSI1. The other, G and SI1. With the naked eye, you wouldn’t see much difference, if any. However, you’ll likely have a strong emotional reaction when you compare their prices. The point is simple. These are the rarest quality diamonds. Only a sophisticated diamond appraiser who inspects them carefully under magnification will appreciate their differences.
To summarize, when you choose a diamond, go with quality rather than size. Also, keep in mind that the differences between the rarest quality diamonds may not be worth the price (or even perceptible to anyone but an expert).
1338 E 41st StreetTulsa, OK 74105